Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

These instructions help you configure your Cisco UCME / BE4000 / UC500 to work with TIM Plus. Contact your system maintainer if you are not familiar with the configuration of your PBX.

Pbxsummary
Supportfiles1Cisco UCME - SysLog.TDT
Supportfiles2Cisco UCME - SysLog.TDS
ConnectionSysLog connection
RequiredTask1Configure Cisco AXL sync
RequiredTask2Configure UCME to send SysLog events
RequiredTask2RequiredTask3Configure TIM Plus to capture SysLog packets

HTML
<a id="Configure Cisco AXL sync

...

"></a>

Configuring Cisco AXL sync

Follow the steps below to configure TIM Plus to perform directory synchronisation with your Cisco UCME:

  1. Click on the Directory tab.
  2. Choose the site you want to configure and click Properties.
  3. In the Site Properties window, select the Sync tab.
  4. Tick the option entitled Synchronise with the following device .
    Screenshotmacro
    Borderfalse
    URL/download/attachments/12158183/cisco_ucme_3.png
  5. In the Host field, enter the IP address of your UCME.
  6. In the 
    Referencemacro
    LabelPort
     field, enter the port number of the IOS service, e.g. 
    Keywordmacro
    Label23
     .
  7. In the Username field, enter the username of the IOS login that can perform synchronisation.
  8. Click on the Set button and enter the password of the IOS login that can perform synchronisation.
  9. Click on the Save button to apply the changes.
HTML
<a id="Configure UCME to send SysLog events"></a>

Configuring UCME to send SysLog events

Login to your Cisco UCME / UC500 via telnet, Use Telnet to connect to the IP address of your UCME as shown below:

Screenshotmacro
Borderfalse
Shadowfalse
URLhttp://docs.tri-line.com:8090/download/attachments/12158183/cisco_ucme_4.png

Now just Once connected, enter the following SysLog commandscommands to enable the UCME to send SysLog events to TIM Plus:

StepIOS commandsDescription
1enableEnter Causes the UCME to enter EXEC mode, enter . Type your EXEC password if requested.
2conf tEnter Enters the global configuration mode.
3aaa new-modelEnable Enables aaa accounting mode.
aaa accounting connection h323 start-stop group SysLog
gw-accounting syslog
acct-template callhistory-detail
4logging 192.168.10.1Specifies the IP address to send CDR data. Where 'of TIM Plus's SysLog server, to which CDR data will be sent, e.g. 192.168.10.1' is the machine running TIM Plus.
5endExit Exits configuration mode.
6wrSave Saves changes.
HTML
<a id="Configure Cisco AXL sync"></a>

Configuring Cisco AXL sync

Below you will find steps on how to configure the Directory Sync from Cisco UCM:

...

TIM

...

Screenshotmacro
Borderfalse
URLhttp://docs.tri-line.com:8090/download/attachments/12158183/cisco_ucme_3.png

...

HTML
<a id="Configure TIM Plus to capture SysLog packets"></a>

Configuring TIM Plus to capture SysLog packets

Below you will find steps on how Follow the steps below to configure TIM Plus to receive SysLog data from your Cisco UCMUCME:

  1. Browse to TIM Plus as normal and login with your credentials.
  2. Click on the Directory tab.
  3. Select Choose the site configured during the setup wizard you want to configure and click Properties.
    Screenshotmacro
    Borderfalse
    URLhttp://docs.tri-line.com:8090/download/attachments/12158185/cisco_ucme_6.png
  4. Within In the Site Properties window, select Cisco UCME - SysLog from the PBX model drop-down list.
  5. In the Connection method field, select SysLog connection from the drop-down list.
  6. In the Client IP field, enter in the IP Address address of the Cisco UCME / UC500.
  7. Finally, click Click on the Save button to apply the settings.