Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

After installation, the settings wizard the 

Referencemacro
LabelEcho settings
screen will appear, where you are prompted for various pieces of information to help set up Echo successfully on your network:

Image Removed

can configure the options detailed below:

VOIP

Screenshotmacro
Borderfalse
Shadowfalse
URL/download/attachments/11043018/config_1.png

FieldDescription
Choose a nameEnter a unique name to identify this installation; if you are installing more than one instance of Echo on your network, the name you enter here will be used in the subsequent setup of your TIM Plus or TIM Enterprise server.
Network adapterChoose the adapter that will receive SIP/SCCP and media packets from your network.

...

Buffer sizeThe socket buffer value is the maximum size (in bytes) that you'd expect your network adapter to receive from your network.

...

The default value of 65536 should be sufficient for most networks

...

Web server settings

SettingDescription
Port

The port number that the internal web service that Echo should listen on

UsernameUsername required to access the Echo web service
PasswordPassword required to access the Echo web service

Audio settings

SettingDescription
QualityThe desired quality of audio recordings after compression.  The higher the quality, the better the audio will sound but the bigger files on disk will be
Compress timeoutThe amount of time (in seconds) that Echo will wait for an audio file to be compressed.  Usually the default setting on 2400 seconds (40 minutes) is more than sufficient.
FolderIf you want to specify a custom folder to place finished audio files in, press this button and choose a path.

Monitor settings

 
SettingDescription
Packet typesThe types
ProtocolsThe types of IP packets that you know Echo should look for when inspecting passing traffic on your network adapter. If you know for sure that your audio signal or media packets will never be TCP packets, you should deselect TCP to save CPU load; the less traffic that Echo needs to inspect, the more concurrent calls it can handle with the same hardware.
SIP port(s)The UDP/TCP port number(s) that will be used for SIP signalling traffic on your network.   Usually this is a single port (5060) but, in the case of media proxies or multiple SIP registrars on the same network segment, further ports may need to be entered here.
Cisco SCCP portThe TCP/UDP port that you expect Cisco SCCP (Skinny) packets to be transmitted on.   This value is normally port 2000.
Session timeoutEnd session if no audioThis value specifies (in seconds) specifies the maximum amount of time that Echo will continue monitoring a SIP or SCCP session in the event of no traffic, before it considers the session abandoned.

...

Web server

Screenshotmacro
Borderfalse
Shadowfalse
URL/download/attachments/11043018/config_2.png

SettingDescription
PortThe port number to use for the internal Echo web service
UsernameThe username required to access the Echo web service
PasswordThe password required to access the Echo web service

Audio

Screenshotmacro
Borderfalse
Shadowfalse
URL/download/attachments/11043018/config_3.png

SettingDescription
QualityThe desired compression quality for audio recordings. The higher the quality, the better the audio will sound but the bigger the files will be.
Compress timeoutThe amount of time (in seconds) that Echo will wait for an audio file to be compressed. By default, this is set on 2400 seconds (40 minutes).
ChangeBy default, the audio files are stored in the following location:
Referencemacro
LabelC:\ProgramData\Tri-Line\Echo\audio
. To select a different folder, click on the
Referencemacro
LabelChange
button and enter the preferred location.

When you have finished configuring Echo, click on the Apply button to save the settings to disk and then start the Echo service.

Info

You can verify that the Echo service is running by connecting to its web service at: http://localhost:80808088/. If you changed the Web server settings (above), the address may differ.